Artinfuser Algo: File

Uploaded: 2019-08-04 13:28:42 by Mike Hirst
Total files size on disk: 6.93 KB
Midi file duration: 00:00:16
Midi file PPQ: 480 (notes start from track 1)

Task progress: Success in 2 seconds
Task created: 2019-08-04 13:28:42 by Mike Hirst (Upload new file)
Task queued: 2019-08-04 13:28:49 by Mike Hirst
Task started: 2019-08-04 13:28:49 on server #1
Total task run duration: 00:03
Algorithm run duration: 00:00
Stages render duration: 00:00
Waveform and service run duration: 00:02

Algorithm: Correct 2-voice music

Change music rules for this task:

General settings

Visibility:

include "include/CA2.pl"

method = swa # This method is best for analysis and corrections in most cases
max_correct_ms = 10000 # Maximum time in milliseconds to correct using window-scan (set to 0 to scan up to the end)

t_cnt = 100000 # Maximum number of steps generated
midifile_export_marks = 1 # Set to export marks (harmony) to midifile lyrics
midifile_export_comments = 0 # Set to export comments (violations) to midifile lyrics
show_correct_hatch = 1 # Set to 1 to mark corrected notes with hatch

AutoLegato = 50 # Enables auto legato for all instruments, converting touching notes into legato transitions (can be overridden for particular instruments). Usually can be used if you do not use slurs in your score and want all adjacent notes to be legato
unison_mute = 1 # 0 - do not mute unisons; 1 - mute unisons in voices with same instruments
reverb_mix = 30 # Control reverb mix from 0 to 100% (0% is totally dry, 100% is totally wet)
rnd_tempo = 6 # Randomize tempo not greater than this percent
rnd_tempo_slow = 1 # Tempo randomization function slowness

show_ignored_flags = 0 # Show even ignored flags (with strikethrough in rules.xlsm)
show_allowed_flags = 0 # Show even allowed flags (bold in rules.xlsm)
show_min_severity = 49 # Minimum severity to highlight note
prohibit_min_severity = 49 # Rules with severity below this can be violated
species = 0 # Do not override parameters in importing files

cantus_high = 0 # 0 - auto detect. 1 - lower cantus. 2 - upper cantus
cantus_id = 1 # Start analysis from this cantus id (numbering starts from 1)
harm_notation = 3 # Harmonic notation (see configs/harm/harm-notation.csv for details)
tempo_bell = 1.3 # Increase tempo in the middle of cantus / counterpoint. 0 - preserve source tempo
show_hatch = 0 # 0 - show no hatch, 1 = show dissonance hatch, 2 = show msh hatch
show_harmony_bass = 2 # 0 = do not show bass, 1 = Show harmony bass, 2 = Show chord type (6 or 64)
ly_rule_verbose = 1 # 0 - Show only rule name up to colon. Show only subrules starting with colon, 1 - Add subrules without colon, 2 - Add rule comments

Midi_file = "server\cache\2019-08-04-Cm.mid"
corrections = "1" # Enable correcting notes. Injected by Mike Hirst at 2019-08-04 13:28:42
ctools_task_id = "66191"
ctools_file_id = "1510"
ctools_file_name = "Cm.mid"

You cannot change config because this file belongs to other user.

Pending task changes:

Config changes since 2019-08-04 13:28:49 (render 1):

All task changes:

2019-08-04 13:28:42 corrections = "1"

Example and include configs Instrument configs

Files with same name or same content, ordered by upload time

File name	Content	Upload time	Uploaded by
cm.mid	Different #22432	2023-06-11 18:44:24	Stephan Pfalzgraf
cm.mid	Different #22432	2023-06-11 18:41:50	Stephan Pfalzgraf
Cm.mid (this file)	This file	2019-08-04 13:28:42	Mike Hirst

Apply this config to new MIDI file

Download source file